Pattern Corrections

Book Number 2

BRIDGET (pg 4)

Yarn Quantites size B should be 17 balls

CLEA BERET (pg 7)

The way to increase in this pattern is to knit into the front and back of a stitch (ie Kfb NOT M1)
Row 11 [108 sts] (not 111sts)
Row 25 (RS) [K6, K2tog]10 times, K1 [71 sts]
Row 27 (RS) [K5, K2tog]10 times, K1 [61 sts]
Row 29 (RS) [K3, K3tog]10 times, K1 [41 sts]
Row 31 (RS) [K3tog]13 times, K2 tog [14 sts]

COCO (pg 9)

First column, 3rd row down "42, (46, 50, 54) shaping rows" should be AFTER the "work 3 rows"
The Front ends up being 7 rows shorter than the Back - this is correct

HOLLY (pg 10)

Yarn Quatities should be 14 balls.
The pattern for Holly Shawl is as follows:
Cast on 120 sts
Row 1 (RS): *P4, k2, p1, k1, p1, k1, p1, k1, p6, k2, p4; rep from * to end.
Row 2 (WS): * K12, p1, k1, p1, k1, p1, k7; rep from * to end.
Row 3: As row 1.
Row 4: As row 2.
Row 5: As row 1.
Row 6: As row 2.
Row 7 (RS): *P4, k2, sl next 7 sts onto cable needle and hold at back of work, p5, [p1, k1, p1, k1, p1, k1, p1, from cable needle], k2, p4; rep from * to end.
Row 8: *K7, p1, k1, p1, k1, p1,k12; rep from * to end.
Row 9: * P4, k2, p6, k1, p1, k1, p1, k1, p1, k2, p4; rep from * to end.
Row 10: As row 8.
Row 11: As row 9.
Row 12: As row 8.
Row 13: As row 9.
Row 14: As row 8.
Row 15: * P4, k2, sl next 5 sts onto cable needle and hold at back of work, p1, k1, p1, k1, p1, k1, p1, [p5 from cable needle], k2, p4; rep from * to end.
Row 16: As row 2.
Repeat these 16 rows until length measures 200cm or length required and cast off.

ISOBELLE (pg 11/12)

LEFT FRONT.. switch Next row (RS) and Next row (WS).
Page 12 ..after working straight to 48 cm , work the WS then RS row. Repeat last 2 rows 4 times (all sizes)... Work 5 rows straight (all sizes).
RIGHT FRONT.. work 4 rows straight (all sizes) .
BACK.. switch RS row and WS row as for fronts.

JUNIPER (pg 14)

Making Up Line below Row 1 (WS) should read
marker, P2tog tbl, slip marker to right needle , P2tog

MOUNTOLIVE SOCKS (pg 16)

TO TURN HEEL replace with
Row 1 K13, K2tog, K1, turn.
Row 2 P6, P2tog, P1, turn.
Row 3 K7, K2tog, K1, turn.
Row 4 P8, P2tog, P1, turn.
Row 5 K9, K2tog, K1, turn.
Row 6 P10, P2tog, P1, turn.
Row 7 K11, K2tog, K1, turn.
Row 8 P12, P2tog, P1, turn [14 sts].
Row 9 K14, thus completing heel.
Slip all instep sts onto one needle again. Slip last 7 sts worked onto another needle.
Using this needle holding 7 sts, K up 12 sts along side of heel. With a second needle, K across 22 instep sts. Using a third needle, K up 12 sts along other side of heel, then rem 7 heel sts [60 sts].

REBECCA (pg 19)

Left column 3rd row down. Inc row (RS) should be...Knit to marked st, up 1, K the marked st, up 1, k to Cable Panel, work Cable Panel, k to marked st, up 1, K the marked st, up 1, k to end.
Before row 25 insert -Work 1 row.
Row 28 should read Work 3 (3, 1,1,1) rows straight.

TASH HAT (pg 20)

Row 7 ..P1, [p2tog, k6(or C6B), p2, p2tog] 5 times.

TURTLEDOVE (pg 21)

Sleeves - after "These 2 rows set the pattern" insert Change to 5mm needles.